View E1100ACETC-24000M-CL175_4530229.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Marketing Bulletin
DATE: TO: FROM: RE: May 6, 2005 All Sales Personnel Mark Stoner E11 (OS/03) Termination
To all concerned parties, This bulletin is to notify all customers of the discontinuation of the following Ecliptek series effective May 1st, 2005: Series E11 Description 5V 14 pin DIP ECL Oscillator Recommended Replacement None
In compliance with our End of Life (EOL) policy, this will serve as advanced notice of product termination. New orders will not be accepted after August 1st, 2005, with delivery to conclude by November 1st 2005. If there are any questions pertaining to this bulletin, please fell free to contact me. Thank you again for your cooperation.
Best Regards,
Mark W. Stoner Director of Marketing Ecliptek Corporation
3545 CADILLAC AVENUE * COSTA MESA, CA 92626-1401 * (714) 433-1200 * Fax (714) 433-1234
STANDARD SPECIFICATIONS
Frequency Range: Frequency Tolerance/Stability: 00 45 25 Operating Temperature Range Blank ET Storage Temperature Range Supply Voltage (VEE ) Input Current Output Voltage Logic High Output Voltage Logic Low Rise/Fall Time Duty Cycle Load Drive Capability Aging @ 25C Fine Leak Test: Gross Leak Test: Mechanical Shock: Vibration: Lead Integrity: PIN 1 7 8 14 6.000MHz to 155.520MHz (All Values Inclusive of Operating Temp. Range, Supply Voltage, and Load) 100ppm Max. 50ppm Max. 25ppm Max. (0C to +70C only), (less than or equal to 125.000MHz only) 0C to +70C -40C to +85C -55C to +125C -5.2Vdc 5% (AA, AB, and AM); +5.2Vdc 5% (AC) 140mA Maximum -1.0Vdc Min./-0.7Vdc Max. (AA, AB, and AM); 4.0Vdc Min./4.5Vdc M ax. (AC) -1.95Vdc Min./-1.60Vdc Max. (AA, AB, and AM); 3.00Vdc Min./3.42Vdc Max. (AC) 2nSec Maximum (Measured at 20% to 80% of waveform) 50% 10% (Measured at 50% of waveform) 50 Ohms into -2.0Vdc (AA, AB, and AM); 50 Ohms into +3.0Vdc (AC) 5ppm/year Maximum
OBSOLETE
ENVIRONMENTAL & MECHANICAL
MIL-STD-883, Method MIL-STD-883, Method MIL-STD-202, Method MIL-STD-883, Method MIL-STD-883, Method 1014, Condition A 1014, Condition C 213, Condition C 2007, Condition A 2004 Solderability: Temperature Cycling: Resistance to Soldering Heat: Resistance to Solvents: MIL-STD-883, Method 2002 MIL-STD-883, Method 1010 MIL-STD-202, Method 210 MIL-STD-202, Method 215
PIN CONFIGURATIONS
AA Ground/Case -5.2V Output Ground AB No Connect or Complementary Output -5.2V Output Ground/Case AC No Connect or Complementary Output Ground/Case Output +5.2Vdc AM No Connect or Complementary Output Ground/Case Output -5.2Vdc
PART NUMBERING GUIDE
E11 00 AM ET C - 24.000M - CL175
Configuration Options CLXXX = Cut Leads (MAL01-101-000) G = Gull Wing (MAL01-001-000) Frequency Pin 1 Connection Blank = No Connect C = Complementary Output Operating Temperature Range Blank = 0C to +70C ET = -40C to +85C Pin Configuration AA, AB, AC, or AM Per Pin Configuration Table Above Frequency Tolerance/Stability 00 = 100ppm Maximum, 45 = 50ppm Maximum 25 = 25ppm Maximum
7.620 0.203
1
15.240 0.203
0.9 MAX
7
0.457 0.1 (X4)
14
8
5.08 MAX 13.2 MAX 5.08 MIN
MARKING GUIDE
(Line #1) ECLIPTEK (Line #2) E11 AM C
Pin 1 Connection Blank = No Connect C = Complementary Output Pin Configuration Per Pin Configuration Table Above
20.8 MAX
ALL DIMENSIONS IN MILLIMETERS
SPECIFICATION CONTROL DRAWING
Drawing Number
(Line #3) XXX.XXXM
Frequency
CSC01-010-000
Title
(Line #4) XX Y ZZ
Week of Year Last Digit of Year Ecliptek Manufacturing Code (TEN02-001-000)
ECLIPTEK E11AMC XXX.XXXM XXYZZ
FULL SIZE ECL OSCILLATOR
Revision Effectivity Date
E
ECN Number
08-27-03 PAGE 1 OF 2
Date Released By Date
8675
NOTE: Pin 1 shall be marked with a black dot. Marking shall conform to conditions listed in TQC41-001-000.
Approved By

▲Up To Search▲

Price & Availability of E1100ACETC-24000M-CL175

	To Download E1100ACETC-24000M-CL175 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .